What You'll Need
- Genie Garage Door Opener One Button
- Garage Door Opener One Light Green One Yellow
- Garage Door Opener Installation Youtu…
- Installing Garage Door Opener One Piece Door Handles
- Cost To Install Garage Door Opener
- Garage Door Openers Installed Price
- Installing Garage Door Opener One Piece Door Handle And Deadbolt Set
A drill
Pliers
Read our FAQ's regarding your Genie garage door installation or call customer service at 1-800-35-GENIE. Before installing a Genie opener. Difficult to handle. Replacing the lock or handle on a garage door can be accomplished with the appropriate tools. Replace a garage door lock or handle with help from a garage door specialist in this free video clip. Use impact driver to mount hinges to the bottom panel of garage door. Stand the bottom door panel on the floor in the garage doorway. Insert rollers into the brackets attached to the door. Stand track beside door, insert rollers into the track and screw the track to doorway frame. Attach the hinges to the second door panel.
A ladder
What You'll Need
A drill
Pliers
A ladder
One piece garage doors may be of 2 types: manual or automatic. Manual doors are easier to install, as there is only the door itself and the handle. Automatic doors are heavier and harder to install because they include a small motor and cables. If you have bought a solid wood door for your garage, you will have to get the automatic type, with a motor and cables to sustain and move its weight. Manual doors are considered to be more difficult to break into, as the key is harder to obtain than the radio frequency on which the door is operating; however the automatic doors are more convenient.
The difficulty of the garage door installation will also depend on the type of spring system the door functions on. If you have the standard torsion spring system, it is advisable to ask a professional to install your door, as this system requires manual wounding and can cause injury if not properly handled. The extended torsion spring type is safe for you to install, as it is not wound manually.
Step 1 - Read the Instructions
Read the instructions; this will help you get familiar with the compounds of the garage door.
Step 2 - Measure the Door
Measure the door opening, its height, its width, the height of the headroom (you need the headroom to be as high as the radius of the track).
Step 3 - Assemble the Door
The sections of the door will need to be assembled. Do not remove the old door before you have done this, to be sure your garage will not stay open for a long time.
Step 4 - Install the First Section of the Door
Install the first section of the door. It is important that you make sure the first section of the door is evenly leveled, as you will be assembling the other sections above it.
Step 5 - Tighten the Brackets
Carefully tighten the brackets at the corners of the first section, as they will have to sustain the weight of the door, so make sure they are well in place.
Step 6 - Install Rollers and Tracks
Install the rollers and tracks for the first section.
Step 7 - Install the Rest of the Door Sections
Proceed to installing one by one the next sections of the door with the corresponding sections of tracks and rollers. Check the level after each section.
Step 8 - Install Horizontal Tracks
Install the horizontal tracks on the ceiling. These should connect to the tracks on the walls or slip into them. The horizontal tracks are braced from the ceiling. Use the level here as well. Kon boot usb windows 10.
Step 9 - Place the Spring System
The last thing to put in place is the spring system. Check the manual to make sure you have the extended spring torsion system, if not, call a professional to install it.
Step 10 - Attach the Motor
If you have an automatic garage door you will have to continue by attaching the motor to the ceiling. The motor is heavy, so you will need to attach it to a beam first. Attach the track to the drive unit (the motor). The wires from the motor need to be connected to the wall switch.
Attention! The text in this document has been recognized automatically. To view the original document, you can use the 'Original mode'.
Advertising
Installation
CTpp -in
Connect Door Arm to Trolley
^
Follow only those instructions which apply to your door type.
SECTIONAL DOOR INSTALLATION
Make sure garage door is closed tight. Pull the emergency release handle to disconnect the trolley. Manually move
outer trolley back to the center of inner trolley as shown in Figures A, B and C.
FIG A: Fasten straight door arm section
to outer trolley with a clevis pin. Secure
the connection wittra ring fastener.
Fasten curved section to door bracket in
the same way.
FIG B: Bring arm sections together. Find
two pairs of holes that line up and join
sections.
sections.
Select holes as far ^art as possible to
increase door arm rigidity.
increase door arm rigidity.
Clevis Pin
FIG C: If holes in curved arm are ABOVE
holes in straight arm, disconnect straight
arm. Cut about 6* from the solid end.
holes in straight arm, disconnect straight
arm. Cut about 6* from the solid end.
Reconnect to trolley with CUT END
DOWN as shown.
Bring arm sections together. Find two
pairs of holes that line up and join with
screws, lock washers and nuts.
screws, lock washers and nuts.
Emergency
Release
Handle
Screws
Sri6'-t8x7/8'
V
^ 5n6*-18x7/8'
-Cut This End
Proceed to Step 1, page 17. Trolley will rc'engage automatically when opener is operated.
ONE-PIECE DOOR INSTALLATION
ASSEMBLE DOOR ARM: Fasten straight and curved door
arm sections together to longest possible length. With door
closed, connect straight door arm section to door bracket
with a clevis pin. Secure with a ring fastener
closed, connect straight door arm section to door bracket
with a clevis pin. Secure with a ring fastener
Door
Bracket'
.fling
Fastener
Nuts
sne’-is
Clevis Pin
Straight '
Arm
Screws
5ri8'-18x7/8 -----
Curved
Door Arm
Before connecting door arm to trolley, limits of travel must be adjusted on one-piece doors. Limit adjustment screws
are located on left side panel as shown in illustration on Page 17. Follow procedures below.
OPEN DOOR ADJUSTMENT
Genie Garage Door Opener One Button
Decrease UP
limit.
Turn UP limit adjustment screw counterclock
wise 4 complete turns.
Garage Door Opener One Light Green One Yellow
Press Wall Control push button. Trolley will travel to full open.
Manually raise door arm to open position (parallel to floor) and
lift door arm to trolley. The arm should touch trolley just in back
of door arm connector hole as shown in solid line drawing. If arm
does not extend far enough, adjust limit further. One full turn
ADJUSTMENT PROCEDURES
CLOSED DOOR ADJUSTMENT
Decrease DOWN
limit.
Turn DOWN limit adjusinnent screw clock
wise 8 complete turns.
Press Wall Control push button. Trolley will travel to full dosed.
Manually close door artd lift door arm to trolley. The arm should
Garage Door Opener Installation Youtu…
touch trolley just ahead of door arm connector hole as shown in
dotted line drawing. If arm is behind the connector hole, adjust
dotted line drawing. If arm is behind the connector hole, adjust
Installing Garage Door Opener One Piece Door Handles
limit further. One full turn equals 2' of door travel.
equals 2' of door travel.
CONNECT DOOR ARM TO TROLLEY: With door closed, join curved arm to connector hole in trolley with remaining clevis pin. Secure
with a ring fastener, NOTE: It may be necessary to lift door slightly to make connection.
with a ring fastener, NOTE: It may be necessary to lift door slightly to make connection.
Magic iso maker 5 5 magic disc download. Run opener through a complete travel cycle. If door has a slight 'downward* slant in full open position, decrease UP limits until door
is parallel to floor.
is parallel to floor.
16
Advertising
Cost To Install Garage Door Opener
This manual is related to the following products:
Garage Door Openers Installed Price
Popular Brands
Installing Garage Door Opener One Piece Door Handle And Deadbolt Set
Popular manuals